13 Amp Fused Spur Wiring Diagram

An FCU is fitted with a fuse holder in the face-plate that takes a 3 amp fuse for appliances using up to 700 watts and a 13 amp fuse for appliances using higher wattage. May be faulty or the total load of 13 Amps 3120 Watts has been exceeded.

Tech Trendiswitch

Fused Connection Units are available with Neon Indicators Flex Outlets.

13 amp fused spur wiring diagram. Orders that include Big and Bulky items will incur an additional delivery charge. For a 3 Amp connection unit the total load should not exceed 720 Watts. The Andris Lux range is unvented ie.

The first image is how the back of your double socket should look and the second is the wiring for a spur. This is in its own RCD protected circuit. Can units be wired to a 13-amp plug.

In the first diagram the first spur from the RCBO is to serve a water heater and the second spur from the RCBO is to serve a feature fire which. 2 depths of frontplate available to allow for flex outlet and concealed wiring options. Guide to connecting equipment to a socket-outlet circuit.

You can see how to wire a spur to an existing socket from the images below. Familiarise yourself carefully with the location of the terminal connectors before wiring follow diagrams below ensure no bar wires protrude from the terminals rocker switches do not need to be earthed due to the plastic face plate screw frame into backpattress box in wall. Using a flat bladed screw-driver carefully leaver open the fuse carrier.

It is absolutely vital that the terminal screws do not clamp on the insulation of the cables. In all fairness if the cooker was to overload the socket the 13Amp fuse in the socket would blow. The diagram shows connections for a ring main circuit.

13 AMP UNSWITCHED FUSED CONNECTION UNIT Fitted with a 13 Amp fuse. The ring final circuit is rated to 32Amp total load and should be wiredcable sized to handle this current so from the point of view of a consumer plugging in an appliance via a 13Amp plug socket which does NOT blow the plugs fuse and or circuit breaker from a socket then there should be no problem. FCU units can come with or without a switch but if it is not fitted with a switch the appliance it supplies must have an onoff switch.

3 GANG AND 6 GANG 2 WAY SWITCH Connect the cables as shown in the wiring diagram. Connect the new socket or switch as shown in the appropriate wiring diagram in these fitting instructions taking care that only the copper conductors enter the terminals. The new oven hasnt come with any wires just a black plate at the back to connect the LN and earth into.

Connect the cables as shown in the wiring diagram. When used on a ring main there will be two supply cables. Stylish modern profile.

Yes you can use higher the reason you can use a 15mm cable is the fact that its been fused down to a max of 13 amps and yes you can go higher the only problem i can see with what you are suggesting is the loading if you have a fridge washing machine and tumble dryer all off a fused spur there will be a good chance the FCU is over loaded what i would suggest is that you either cut into the. BG 13A Single Double Pole Fused Spur Connection Unit. Why do I need an expansion vessel.

However the electrician now says he is concerned that because the fused spur is fed radial from a socket not wired directly to form part of the ring final then the load at the first part of the circuit from skt to spur could exceed the rating of the cable supplying it and he needs to go and do some calculations. The subtle design will blend with any dcor - suitable for domestic or commercialinstallations. Clipsal fused spur wiring diagram.

Ensure that the load cable is connected to the appliance. 13 AMP DOUBLE POLE SINGLE SWITCHED SOCKET Connect the cables as shown in the wiring diagram. The old oven was wired into a 13A fused spur behind the unit that came off a cooker isolator switch located above.

A general rule for a ring main is that if you only have two cables in the back of an existing socket then it is ok to spur. Insert the appropriate BS1362 fuse in to the RCD Spur. 13A DP UNSWITCHED FUSE SPUR 13A DP SWITCHED FUSE SPUR NO NEON.

Standard delivery - from FREE. DO READ THESE OPERATION INSTRUCTIONS AND STRICTLY OBSERVE THE TEST PROCEDURE AFTER INSTALLATION AND WHEN CHANGING THE FUSE TEST PROCEDURE Stage 1. Please refer to our Delivery Details for more information.

13 Amp RCD Fused Connection Unit Brief product description. So basically a spur of a spur is never permitted even if its fused. Ill have to just stick in a juntion box in the ring cables under floorboard and get a fused spur off that.

Note - the fuse carrier cannot be fully removed from the product. 13 Amp Fused Connection Units Brief product description. They may also have a neon indicator light.

Fit a new fuse to BS1362 and push the carrier home so it sits flush with the surface of the faceplate. 13 Amp RCD Fused Connection Unit Replacing the fuse 1. Line Diagrams The subtle design will blend with any dcor - suitable for domestic or commercial applications.

Put a 13amp unswitched spur adjacent to the socket then you can run whatever. Standard delivery - from FREE. There is an integrated RCD to prevent the leakage of electrical current.

If in doubt consult a qualified electrician 9. Pressurised and when the water is heated. Connect both of the cables to the same terminal.

4 or FREE over 75. Pull the carrier out and replace the fuse. Both the Andris Lux and Andris Lux Eco can be wired to an appropriate fused spur.

This seems really odd to me. 13 AMP DOUBLE UNSWITCHED SOCKET Connect the cables as shown in the wiring diagram. For radial circuits or a spur off a ring main there will only be one cable.

Fused Connection Unit Wiring Fcu How To Wire Fused Spur Youtube